Autel Robotics Remote Controller (for Nano and Lite Drones)

EVO Nano series adopts the new generation of Autel Skylink image transmission technologyof Autel Robotics, has strong anti-interference capability and supports the double-emissionand double-receiving of 2.4GHz, 5.8GHz and 5.2GHz. It can complete the control and settingof aircraft and camera within at most 10km communication distance (FCC, no interference, no blocking) and can display a high-definition picture in mobile device in a real-time manner by Autel Sky App.(2.7K within 1 miles)

The telescopic mobile device support can stably support the mobile device, and the built-in battery of remote controller is 3930mAh that can work for about 3.5h.

Remote controller Features

• Autel EVO Newest remote controller is ergonomically designed to fit in the palm of your hand
• Strong transmission performance, remote controller supports the double-emission and double-receiving of 2.4GHz, 5.8GHz and 5.2GHz. It can complete the control and settingof aircraft and camera within at most 10km communication distance (FCC, no interference, no blocking) and can display a high-definition picture in mobile device in a real-time manner by Autel Sky App.(2.7K within 1 miles)
• The built-in battery of remote controller is 3930mAh that can work for about 3.5h.
• The sensitive gimbal control wheel can take beautiful pictures as you like.
• The remote control comes with a cable of suitable length, so you don't have to worry about losing it or worrying about it being too long or too short to affect the control of the drone.
• It is made of hard-wearing and sturdy material that won't leave annoying scratches on the surface during everyday use

Remote controller Use

Turn on/off remote controller

1. Startup

   Press the power button ( ) for 2s till that a short beep sound appears.

2. Shutdown

   Press the power button ( ) for 2s till that a short beep sound appears.

Important:

• Be sure to turn on the remote controller before the aircraft power supply is connected.
• Be sure to turn off the aircraft power switch before turning off the remote controller

Charge remote controller

1. Short press the power button ( ) once to check the current battery level of the remotecontroller, and charge the remove controller if low battery level.
2. Connect the special charging cable to the USB-C interface at the bottomof the remotecontroller. Full charge takes 2h.

1. In the case of charging, the power indicator of the remote controller will enter the mode of waterfall light. After completion of charging, the four indicators will be normally on green. At that time, you will hear two beep sounds.
2. Disconnect the charger from the remote controller after completion of charging.

Remote controller Calibration

If the command stick is abnormal (the remote controller falls on the ground or the flight direction of the aircraft is not consistent with its operation direction), the remote controller is recommended to be calibration. You can calibrate the remote controller by using Autel Sky App

1. Please turn off the aircraft power supply before operation.
2. Open Autel Sky App, enter the setting interface, click the “control” option, click the “remote controller calibration”, and then click the “start” key.

1. Move the left and right command sticks and thumbwheel in turn to their maximum extent in the direction of the arrow on App. When the calibration of a direction is completed, the arrow in the direction will become blue.

Remote controller Pairing

The remote controller and the aircraft have been paired in the factory. If the remote controller needs to be paired again after replacement, please follow these steps:

Method 1

1. Turn on the aircraft and the remote controller, double-click the aircraft battery button. The LED on the rear of the aircraft will flash quickly to show it is ready to pair
2. Connect your remote controller and mobile phone, operate Autel Sky App, click “Connect New Aircraft” in “Personal Center,” and follow the pairing instruction.
3. After successful pairing, the LED at the tail of aircraft will be on for 5 seconds and then flash slowly. The App will switch to the image transmission interface

Method 2

1. Turn on the aircraft, double-click the aircraft battery button. The LED on the rear of the aircraft will flash quickly to show it is ready to pair
2. Press and hold the power button ( ) and the home button ( ) on the remote controller at the same time for 3 seconds to turn on the remote controller. The remote controller indicator will flash quickly to show it is ready to pair.
3. After successful pairing, the LED at the tail of aircraft will be on for 5 seconds and then flash slowly

Remote Controller Specification